Lecture 6 on Topic 6: Glass Shaping
MIT OpenCourseWare
Glass viscosity marks 0:17
Several reference points define how glass can be shaped. The working point is around 10^3 pascal seconds. Below it, glass flows too easily to hold form. The softening point is around 10^6.6 pascal seconds. Above it, the melt is too stiff to deform. Between them is the working range, where glass can be shaped and then frozen by cooling. The kneeling point is around 10^12 pascal seconds, where internal stress can still relax without changing the macroscopic shape.
Temperature and structure 4:30
Temperature is the simple control knob for viscosity. The same idea applies to amorphous polymers, which move from hard plastic to rubbery material and then to a liquid as you heat them. Adding benzene-like stiff groups raises viscosity and Tg. Adding a plasticizer lowers Tg by reducing friction. In inorganic glasses, higher network connectivity means higher viscosity and higher processing temperatures. Silica sits at the high end, while borosilicate glass is easier to process than silica but harder than soda-lime glass.
Shear rate matters 16:03
Viscosity is not only set by temperature. It also depends on shear rate. A Newtonian fluid keeps one constant viscosity, so stress rises in direct proportion to strain rate. Other fluids thin as you shear them, or thicken instead. A Bingham plastic stays solid-like until stress passes a threshold, then it flows. Toothpaste is one example.
Measuring glass flow 19:03
Shear thickening can come from hydroclustering, where particles gather into larger groups under strong shear and resist motion. Paint is engineered to shear thin so you can brush it on, then it stops flowing. Soda lime glass also shear thins, which matters in fiber drawing. Different viscosity ranges need different tests, from rotating cylinders to plate setups, beam bending, and optical interference.
Room temperature flow 32:32
At room temperature, glass is treated as an elastic solid because its viscosity is so high. The estimate is around 10^24 to 10^25 pascal-seconds, and that means a piece would take about a billion years to move only one nanometer. The old window pane story is explained the same way: the thicker side was placed at the bottom during assembly. The slower flow in old panes is not the reason for the shape you see.
Shaping with viscosity 38:01
Glass is useful because its viscosity changes smoothly with temperature. You can tune it into a range where it softens without collapsing, unlike a crystal that jumps from solid to liquid at its melting point. Most shaping is done in a working range, while flow glass uses lower viscosity for sheet making and precision molding can use high pressure at higher viscosity. Annealing in a lehr relieves stress, and glass types such as soda lime, borosilicate, and fused silica differ in their working temperatures and thermal expansion.
Waste glass in the melt 46:30
Broken and used glass, called cullet, is added to the raw feed for the furnace. It softens before the fresh minerals reach full melting, so an early liquid phase forms. That helps diffusion and reaction move faster than they would in a solid mix, which cuts the energy needed. The example given is simple: defective bottles are not repaired but sent back into the batch because the glass is useful again.
Flat glass by continuous flow 48:30
The molten glass then moves onto a floating bath of tin, which is denser than glass and holds the melt on top. Surface tension and gravity spread it into a flat sheet. After that, an annealing lehr relaxes internal stress before the sheet is cut and packed. The temperature falls steadily along the line. The same flow process is used for window glass, architectural glass, and even very thin cover glass.
Coatings and surface control 1:08:32
A tin layer is added because it makes the glass surface harder and less likely to scratch. That matters because surface defects are the weak point where cracks can start and spread. The tin also helps the later polymer coat stick, since the polymer is hydrophobic and plain glass is not. The polymer layer is very thin, only a few hundred nanometers, so it burns away in recycling with little effect. The process also removes sodium from soda-lime glass by reacting it into a water-soluble salt, then rinsing it off.
AI-generated summary. It can be wrong or incomplete - check anything that matters against the original.

